Tupo-2 Wall Plastering Machine
Application wall plastering machine:
1.Automatic cement/mortar/lime/gypsum wall plastering machine used in
plastering inside walls.
2.It’s capable to render on bricks and blocks with cement mortar,
ready mix ,
lime mortar and gypsum mortar.
Standard parametersTupo-2 plastering machine
Plastering Capacity (8 hours )
380V/220V standard is 220V/50Hz single phase
standard up to3.5M , special up to 5M
Length of plastering trowel
Weight of Machine
1-5Sets 3-7working days
30% deposite, balance before shipment.
One year since delivery
After Sales Service
We offer technical support& spare part.
Main features Tupo-2 plastering machine:
1. Wall Plastering Machine can reach the very top of the roof.
2. feeding mortar by manual control
3.Large hopper can load about 120kg cement.
4.Intelligent Wall Plastering Machinecan make the wall smooth one time within 1min.
5.Two mini vibrators on theMachine can avoid hollowness of walls,
ensured renderingquality and fully adhesive.
6.Machine equipped with omni-directional wheels. You can move it
7.adopt good quality Panasonic PLCcan judge the operation mode of
8.Tupo used it special Power head which is researched and developed
by itself to drill the accessories .highly increase the
manufacturing precision and decrease working error or toleranceof
auto rendering machine.
9.The working efficiency can be 450m²/8h.
Tupo-2 advantage :
1.save 70% labor cost
2.increase productivity 10-15times
3.stable function &easy operate
4.rendering up to 5M
5.render below or above window openings
AIThe installation method of the reinforced concrete chimney
internal steel tube
1 Construction Technology
The principle of pneumatic jacking reverse method as "the
relationship between the cylinder ratio of cement and sahara for
plastering works and the piston" (see Figure 3). In the
conventional lifting assembled the appropriate height of the steel
tube top section (about 10.8 m), close to the top outlet is
provided with a sealing head, this constitutes an open "cylinder",
put it in the "base" of the thickness of the cylindrical
peripheral. The bottom plate is fixed on the base of the steel tube
on the basis of this, the head sealing ring in the above, the
following scope, surrounded by the inner drum wall to form a closed
cavity. The external air source through a pipeline from the bottom
to the closed cavity pass into the compressed air, as for head of
air pressure over group on rough cut plastering tools the tube
(including the head, the weight), and to overcome the friction of
the inner wall of the sealing ring to Jane, steel tube began to
rise. When the pneumatic jacking the tube mouth than the follow-up
section of the width of steel plate, the arc plate volume has
prepared (3 round in a circle) into the cylinder in the subsequent
"base" around the closure, welding, and then to make appropriate
exhaust cylinder down slowly by welding, and the subsequent docking
on the cylinder, cylinder is connected with a long a day. Then the
gas cap can rise, a new group after welding cylinder, cylinder and
cylinder on the butt, so a day plastering tools greater montréal
after day, the stucco plastering youtube cumulative extension tube
to the design height.
2 main technical requirements
2.1 air pressure and air compression cylinder increase is
proportional to the weight, so the pressure is gradually increased,
the gas pressure at the top of the 0.163 MPa. Through calculation,
the thin cylinder of the material allowable stress exceeds the
actual stress is more than 1 times, and thus will not leak or
explosion, the cylinder is safe.
2.2 the base installation verticality control in 1/ less than 2000,
steel how to do plastering tube center deviation should be
controlled in 2000 H/ and less than or equal to 30 mm.
2.3 the United States ASTMA36 steel and domestic steel Q235 are
close, so the use of J422 electrode. In order to ensure the welding
quality, the welding seam is divided into 3 layers, each completed
6 welders are symmetrically arranged simultaneous welding, after
welding each layer, it was confirmed after welding defects, and
then the next layer.